|
Post Reply |
|
Thread Tools | Search this Thread |
03-20-2024, 02:09 AM | #89 |
Captain
511
Rep 882
Posts |
Thank you, much appreciated! I think it comes down to the wall thickness used and that PETG has better layer adhesion than ABS. The backing plate ducts are "solid" and the base of those are 5 mm thick which is considerable mass. In combination with the strengthening ribs and steel backing plates is what makes it work.
__________________
BMW M2 LCI -18 | BMW 520DA Touring M-Sport -12
| BMW Z4 M Coupe -06 | BMW M3 -02 | BMW Z3 Coupe -99 | BMW 740i/6 -96 | BMW M5 3.8 -92 | BMW M535i -87 |
Appreciate
0
|
04-05-2024, 11:30 AM | #90 |
First Lieutenant
179
Rep 331
Posts |
Is anyone running the larger 2.5" kit with wide front wheels? I feel like the bigger the better
__________________
2017 F80 M3 - Mineral White/Amaro Brown
2003 E46 M3 - Jet Black/Cinnamon |
Appreciate
0
|
04-06-2024, 02:24 AM | #91 |
Captain
511
Rep 882
Posts |
I was running 18x10" ET 25 with 265/35/18 (still the same setup) up front on my M2 with a 2,5" kit last year without any big issues. A little wear on the hose on a couple of spots because of turning to full lock/hard compression but that's expected when you want to maximize the hose diameter. I use polyester electrical tape at the critical spots and make sure to change out that tape every year to prolong the life of the hose.
__________________
BMW M2 LCI -18 | BMW 520DA Touring M-Sport -12
| BMW Z4 M Coupe -06 | BMW M3 -02 | BMW Z3 Coupe -99 | BMW 740i/6 -96 | BMW M5 3.8 -92 | BMW M535i -87 |
Appreciate
0
|
04-25-2024, 12:39 PM | #92 |
Captain
511
Rep 882
Posts |
Updated the first page with an installation guide for the clubsport kit as well.
__________________
BMW M2 LCI -18 | BMW 520DA Touring M-Sport -12
| BMW Z4 M Coupe -06 | BMW M3 -02 | BMW Z3 Coupe -99 | BMW 740i/6 -96 | BMW M5 3.8 -92 | BMW M535i -87 |
Appreciate
1
fabje18.50 |
05-01-2024, 03:16 AM | #93 |
Captain
511
Rep 882
Posts |
The installation guide for the rear clubsport kit is now added in the first post!
Some pictures of a complete clubsport kit sent out to ItsaGoose here on the forum. I've managed to dail in the finish of the ABS-sensor arm as well, it appears it needed a lot more cooling.
__________________
BMW M2 LCI -18 | BMW 520DA Touring M-Sport -12
| BMW Z4 M Coupe -06 | BMW M3 -02 | BMW Z3 Coupe -99 | BMW 740i/6 -96 | BMW M5 3.8 -92 | BMW M535i -87 |
Appreciate
0
|
05-01-2024, 12:22 PM | #94 |
New Member
6
Rep 28
Posts |
That's some beautiful design work
|
Appreciate
1
Westersund511.00 |
05-04-2024, 03:02 AM | #95 |
Captain
511
Rep 882
Posts |
My M2 just passed the yearly inspection and the technicians paid extra close attention to the front brake cooling. I guess they thought something would rub lock to lock, the surprised look on their face when it didn't was kinda funny. The front control arm ducts sit around 10 cm/4" off the ground. The rear isn't even close to being the lowest part.
__________________
BMW M2 LCI -18 | BMW 520DA Touring M-Sport -12
| BMW Z4 M Coupe -06 | BMW M3 -02 | BMW Z3 Coupe -99 | BMW 740i/6 -96 | BMW M5 3.8 -92 | BMW M535i -87 |
Appreciate
1
FrankMstein1037.00 |
Post Reply |
Bookmarks |
|
|