Tuner Pros - Opinion on my first log pull (2nd to 3rd gear)

dustinsterk · 08-17-2017, 08:13 PM

First time logging so apologies if I did not capture the correct attributes. Running MHD Stage 1+ on 91 octane on my 2007 335i (mods in signature below):

http://www.datazap.me/u/dustinsterk/...a=2-3-14-23-27

Car feels very strong and pulls hard, but wanted to understand what things I should be looking out for. Something I noticed was that the throttle position was only at 80 while the accelerator was pegged at 99%. Any other red flags or concerns?

Thanks in advance.

--Dustin

racermp · 08-17-2017, 09:16 PM

Looks like....shit. hahah I'm. Lots of.timing corrections in 3

dustinsterk · 08-17-2017, 09:50 PM

Yikes. Yes I see that now. Stage 1+ does recommend a upgraded FMIC and I see the IAT going up and the timing adjustments correlating. Do you think that could be the cause or do I have something else going on here?

inevitab1e · 08-18-2017, 07:09 AM

I'd say the boost target is a little high for your octane setup. I'd either add higher octane fuel or lower the boost target.

JETmn · 08-18-2017, 08:01 AM

Also note this is the N55 section and our MHD is not the same as the N54, so you might want to ask over there.

dustinsterk · 08-18-2017, 08:02 AM

Ah, sorry about that...I read '335i tuning' and didn't even look at the engine model. Thanks all for the feedback, I will move this thread to the other section.

08-17-2017, 08:13 PM	#1
dustinsterk Private 3 Rep 64 Posts Drives: 335i - MT Join Date: Mar 2006 Location: NJ iTrader: (0)	Tuner Pros - Opinion on my first log pull (2nd to 3rd gear) First time logging so apologies if I did not capture the correct attributes. Running MHD Stage 1+ on 91 octane on my 2007 335i (mods in signature below): http://www.datazap.me/u/dustinsterk/...a=2-3-14-23-27 Car feels very strong and pulls hard, but wanted to understand what things I should be looking out for. Something I noticed was that the throttle position was only at 80 while the accelerator was pegged at 99%. Any other red flags or concerns? Thanks in advance. --Dustin __________________ 2007 335i, 6MT, Space Gray/Coral Red, Magnaflow quad tip, CAI's, BOV/CP, FMIC, MHD Stage 1+, BMS Oil Can, Slotted Rotors and Pads, M-sport skirts/front bumper, Carbon interior/rear exhaust diffuser, LCI angle eyes & red tails,18" Forgestar CF5s, Coilovers/Swift springs Last edited by dustinsterk; 08-17-2017 at 08:35 PM..
	Appreciate 0 Tweet Quote

08-17-2017, 09:16 PM	#2
racermp Major 190 Rep 937 Posts Drives: F30 330i Join Date: Apr 2013 Location: Houston, TX iTrader: (1)	Looks like....shit. hahah I'm. Lots of.timing corrections in 3
	Appreciate 0 Quote

08-17-2017, 09:50 PM	#3
dustinsterk Private 3 Rep 64 Posts Drives: 335i - MT Join Date: Mar 2006 Location: NJ iTrader: (0)	Yikes. Yes I see that now. Stage 1+ does recommend a upgraded FMIC and I see the IAT going up and the timing adjustments correlating. Do you think that could be the cause or do I have something else going on here? Last edited by dustinsterk; 08-17-2017 at 11:18 PM..
	Appreciate 0 Quote

08-18-2017, 07:09 AM	#4
inevitab1e Second Lieutenant 49 Rep 220 Posts Drives: '13 135i N55 FBO Join Date: Feb 2017 Location: there iTrader: (0)	I'd say the boost target is a little high for your octane setup. I'd either add higher octane fuel or lower the boost target.
	Appreciate 0 Quote

08-18-2017, 08:01 AM	#5
JETmn Lieutenant Colonel 245 Rep 1,595 Posts Drives: 2011 335i xDrive Msport Join Date: Apr 2013 Location: Orlando iTrader: (0) Garage List 2011 335Xi [0.00]	Also note this is the N55 section and our MHD is not the same as the N54, so you might want to ask over there. __________________ 2011 335Xi 6AT - VRSF catless DP - VRSF 7" FMIC with turbo inlet pipe - VRSF chargepipe - Pure Stage 1 turbo - JB4 - E30 - xHP Stage 3 - Strongflex tension bushings - Whiteline RSFB - UUC rear swaybar
	Appreciate 0 Quote

08-18-2017, 08:02 AM	#6
dustinsterk Private 3 Rep 64 Posts Drives: 335i - MT Join Date: Mar 2006 Location: NJ iTrader: (0)	Ah, sorry about that...I read '335i tuning' and didn't even look at the engine model. Thanks all for the feedback, I will move this thread to the other section. Last edited by dustinsterk; 08-18-2017 at 09:32 AM..
	Appreciate 0 Quote